clutch

Hi: Looking for ideas to solve a sticky clutch on a 2002 Capo. It clunks going into first gear and sometimes hard to find neutral. The back wheel spins in gear when on the centre stand with the clutch lever pulled in. I've changed and bled the clutch fluid and adjusted the grub screw on the...

When I bought the bike it had aftermarket shorty levers on it which work okay. I then bought a new set of "will fit" levers from a nice solid seller on ebay. He has 99.6% feedback and over 12000 sales etc so a proper seller. However I don't like the feel of them and I may be imagining this...

Hey guys has anyone done this swap? Just wondered if there many benefits or not I already have a Oberon slave so it's much lighter with the the standard non radial clutch. Answers on a post card thanks chaps

Hi guys I have just started replacing my spag clutch. The sprag clutch i have removed is slightly different to the genuine rotax sprag bearing i have removed. I belive that the one i have removed is most probally a BMW sprag bearing. Do you know if the rotax sprag bearing needs a circlip as the...

Too cut a long story short engine threw a big end , this engine had a STM mechanical slipper clutch , so I put a replacement engine with the standard Aprilia slipper clutch in. Just wanted too know where the pipes go to on the injectors , I have three pipes all joined to a " Y " piece plastic...

Does anyone have advice for my RSV 1000 Tuono '06. 1. When i keep the clutch pressed for too long, the bike starts creeping and also prevents me fron getting into neutral. -- checkout my Track Picks if you dont have anything to say :D

Right hope someone can point me in the right direction as I am losing the will to live here.... I fitted a replacement clutch slave cylinder a Oberon unit and now I cannot get my clutch to disengage. I have read every how to I can find and still no joy I will tell what I have done and you tell...

As above anyone with a good used clutch master cylinder please contact me :)

I have been working away for the past couple of weeks so not been out on the bike. Last weekend I got home briefly and thought I would go for a spin. The bike had sat for a couple of weeks and had not even been started. It started fine but I had no clutch action at all. I rode it around my...

thinking the reason my clutch lever has no pressure could it be that the pushrod is stuck too far in? thus the clutch cylinder is not able to push the rod in because its stuck too far in? and the fluid is leaking out or the notch cutout in the cylinder spacer? how does this sound to anyone can...

so the next drama of my rsv is this!!! having lost my clutch and all symptoms pointed to the slave cylinder so i replaced this item with an oberon in a lovely red!!! the original one fell apart on the dismantle so it was all looking good to this being the issue , but in typical italian style...

OK - so mine came with gold ones ... I'm sure gold ins lovely but I can't get on with it ... What is the best source - preferably cost effective? ebay just seems to bring up Oberon stuff at 20 quid a pop ... is that the going rate?

Hi guys Just trying to replace my sprag clutch. Every time I try and remove the bolts, its spinning the crank. What is the way around this. Cheers in advance.

Oberon Clutch slave unit excellent condition nicely finished in gold. £50 posted, will accept pay pal gift cheque or bank transfer. pm for dibs

Hi all just got my 2001 Mille with 10000 miles on the clock took her out today and noticed the clutch was slipping when accelerating hard even at 145 in sixth gear do I need to change the clutch or is there something I can do to solve the problem

Hi all, I'm after a standard gen1 clutch lever, specifically the small grub screw part that pushes into the rubber flange when you squeeze the lever. Of course I realise I need to buy the whole lever. Managed to snap this part in a fall (don't ask)

just replaced clutch n now bike smokes occasionally when riding n revving high, is it possible somthing didnt get hooked back up? hopin its not rings or valve seals anyone can help plz

I recently replaced all frictions n steelies but could not replace basket cuz i couldnt get it out, i now found out the whole housing has 2 b removed n i got the gasket, do i need to take off the front cover again or can i just remove the whole housing? n is there anything else thats gotta b...

It works fine, no slip or loss of fluid, its just sometimes when I change gear the lever pulls to the bar like there is nothing there at all, it'll change ok and then next change all is fine again. Happens now and again and not same gear every time, just worried it might be the start of...

Hi Guys, My spag clutch has just gone on my RSV mille 01. I tried to cheap out and took it to a back street garage and the guy doing it has knackered the thread to jack the sprag clutch off. I have taken the bike back now and will do it myself as I have space to do so now. Does anyone have any...