clutch

Would anyone know where I can get the aprilia tuono clutch lever actuating pin and barrel from in the UK. Hopefully not AF1 as it is going to cost about £50 to get it from the states. It might be cheaper going to an engineers workshop and getting them to make one out of titanium. Chhers

Hey guys, I know this has been covered loads of times,my clutch is leaking and I was thinking of replacing the cylinder with an Oberon part. Has anybody used one and are they easy enough to fit?:thumbup Cheers Martin

Hi guys I've only had the tuono a few weeks and I've gotta say I like it im finding the clutch quite heavy and difficult to get into 1st what mods if any can I do to make this easier

Hi, hope someone can help !! While bleeding my wonderful hydraulic clutch. Noticed I had a leak from the master cylinder. Looked round on forum for advice on replacement seals. Ordered the ktm one someone suggested but the piston ones are a different size. Does anyone know which ones fit or...

hello and help I've just whipped off my original levers(vtwin 2010) to replace them, and on each side is a tiny spike shaped object, how the hell do i remove this :banghead, so i can fit to new lever???? many thanks

Hi Need a new clutch slave as mine has decided it's going to leak all over the floor. Anyone got one hanging about, aftermarket preferably but anything cheap considered. Thanks

As above, I've been arguing this with a mate. He seems to think my bike does have a slipper clutch, I don't. I haven't been able to tell by riding it, as I've been riding so long without slipper clutches that I can't bring myself to bang down the box and dump the clutch. I go down a gear at a...

I have a 2000 rsv with the later engine number.Meaning that the first steel I put into the clutch basket has a missing piece on the outer edge.The problem I have is I don't know how many steels and friction plates to use?also is the last one to go in a friction or steel?thankyou for any help

Why is my clutch fluid black again I've bled it twice, is it the hydraulic hose rubber breaking down ? O-rings ect? There's no problem wiv gear changes so will I just av to get some socks for the bottles?

Hi has the 2010 tuono factory got a slipper clutch if so is it adjustable can anybody help.

Anyone got any ideas, my duke clutch tends to fall off because of the heat from the engine, is it the same sort of thing with the mille, do the lines draw air? Or is there something I'm missing? Cheers

Factory clutch problem. It's nearly gone on the lever, air? It's new to me, only done 4600 miles. A known problem? Cheers.

Welcome. I recently just bought my Tuono and I have a problem with a slipping clutch. from what I know that the previous owner poured the wrong oil. I've already bought a scooter Eni Agip 15W50. By the way, I decided to check the clutch plates. According to the manual Rotax V990 whole set should...

Hi all. Haven't posted on here in a long time since I sold my RSVR a few years ago, but now I have bought a 99 reg Falco.... and have had no end of bother with it! :( To cut a long story short: New stator New sprag gear New sprag clutch New clutch diaphragm New speedo sensor New battery All...

need help, clutch lever spungey . bike starts but put in gear bike wants to move. start to let out stalls engine. also rear brake resivoir fluid goes down .own 2007 tuono factory. Thanks for any info

has any one got one of these for sale or know where to get them in the UK Cheers Mark

Has anyone swapped out Hirt non radial type clutch master cylinder to a newer version radial type? I have got a radial M/C and might give it a to as if nothing it's a bit newer and in better condition than the old one, looks like I will probably nex a longer hydraulic line though does anyone...

Hi guys I bought a radial clutch master cylinder off a 2004 rsv factory I was going to fit it to my 2000 mille but to be honest I can't be bothered so I am going to stick with the standard one and sell this. It has a brand new standard lever with it that I got off ebay I think it's a pattern...

I know this may sound a bit gay, but If i wanted to smooth out the ride without having to use the clutch as much especially at low speeds round town, ive heard you can do this by changing the gearing! does anyone have any suggestions on what teeth i will need on the front and rear sprockets to...

Wanted rsv Mille 2001 brake,clutch,gear lever and some engine mounted crash protectors and does any1 know where I can get the washers and spares from to fit my ohlins damper from as they have bin discontinued so my local aprillia dealer can't get them thanks brett plz pm me