clutch

I noticed that my bike is really tough to roll around (when not running), and it has a tendency to "jump" a little bit if I start it in gear, with the clutch lever fully pulled. In neutral it is fine. I don't remember my old Gixxer doing this. Is this normal or do I maybe need to bleed the...

Like the title says I need to get a new one of these for my RSV-R Colin Edwards rep What I want to ask is there any thing better than the standard one and if so what have people fitted please And where the best place to get it

Hi All, If anyone can shed some light on this, it'd be most helpful. When accelerating hard, not every time, but 50/50, when it gets to approximately 7500-8500 revs, it feels as if the clutch is being held in slightly, it over revs, then finds itself again all within about a second. I'm not...

Hi may need to fit a new clutch to my tuono 1000 04 reg has anyone done this job is it straight forword and what make of clutch is best,many thanks.

Hey guys... Should i be pulling the clutch in BEFORE i start my 03 Aprilia RSV? I think not but a friend thinks its best to. Cheers

Hi all, I think I've made things worse. I thought that in advance of doing a slave seal replacement I'd inspect, clean and bleed. I've included some pics. I haven't put the new seal in yet as it hasn't arrived and I never used silicon grease. Oh and it's still leaking! Now though after...

Beringer BRO14 Billet Radial Master Cylinder | eBay Beringer BRO16 Billet Radial Clutch Master Cylinder | eBay

New to this so I hope i'm not repeating myself. Have any of you found a service kit suitable for 2003 RSV1000 clutch master cylinder. Best offer so far is the whole bl---y unit inc lever. Only popped a seal so don't want to waste £200 for a £2.00 seal. Thanks Ant

Hi all. Has anyone had their clutch slave seeping after a bleed? I don't think it's coming from the nipple or banjo bolt as it's at the bottom of the slave and none at the top. It seems to be rock tight, is there a seal in there?

Over winter all the brake fluid in the clutch leaked out of the slave cylinder...(I'm new to RSVR ownership) I found out one day when I fired it up and the clutch did nothing and I had to put some pressure on the gear lever to get the bike into neutral....then I took a look at the empty...

Looking to sell a set of Beringer Master cylinders Brake and Clutch (Titanium in color). Both were on the bike when I purchased it, i'm looking to either sell both of these outright asking $750. The clutch lever is scuffed on the ball, 100% cosmetic I will get some more detailed pictures up...

Hello i need fitting instructions for a stm evoluzione slipper clutch for my 2000 mille r also any fitting tips would be greatly appreciated many many thanks in advance

I bled the clutch MC yesterday and then bled a little at the bottom. Stupidly I undid the banjo bolt instead of the bleed nipple because I didn't notice it. Now there's a tiny bit of fluid seepage and the bite point is further out. Obviously I'll tighten the banjo but is there a way to adjust...

In the 1500 miles I've done since I bought my bike in December I've topped my clutch resovouir up twice and on the last 2 rides the feel of my clutch lever has gone from feeling resistance from full to about half inch from grips and biting point been about 1/2 cm of the grips ! It's still got...

I have a 2000 Mille R and getting a weeping from where the hose from the clutch fluid pot joins into the clutch lever housing, it looks as if the seal may be perishing, is this repairable or will it need replacing for new, if It's a new one then any ideas for the best place to buy......... Only...

Hey all... was riding my bike today... when I get on it cold, the clutch has quite a bit of free play. When I start the bike and put it in gear I only have to let the clutch out a tiny bit and the bike starts moving.. its also hard to get into N. Once I ride the bike for a bit at operating temp...

Genuine aprilia Tuono carbon fibre clutch & brake covers, brand new on ebay for in excess of £83.00 Some secondhand ones went recently for £52.50 each. With this in mind sensible offers considered Cheers Dazzer...

2008 mille r . clutch slip in 4th 5th & 6th gear . got new ebc clutch kit today . fitting it myself , but have already ran into trouble . can anyone tell me how to remove the magnesium cover on the clutch housing .

Does anyone have an old leaking clutch slave please?

hi I have a 1999 RSV mille the bolts have snapped on the clutch plate cover so need to replace the clutch/water pump cover. the number on the inside is 211640 does anyone have this part or know if the later part 6610150 will fit ? any help would be much appreciated. regards Scott