problem

I have a 2000 rsv with the later engine number.Meaning that the first steel I put into the clutch basket has a missing piece on the outer edge.The problem I have is I don't know how many steels and friction plates to use?also is the last one to go in a friction or steel?thankyou for any help

Hi all, Hate to start my first post on this forum with a problem but I’m hoping that you guys can point me in the right direction…. I took the datatool System 3 alarm off recently (thank F*ck for that!) on my 2003 Gen1 Mille and when I went to start for the first time, the fuel pump didn’t...

hi guys i've had my 2000 Mille for just over 1 year now and love it. thanks to the information and guides on here i've done the wiring mods (yellow wires and also the brown connector). on the last few rides, however, i have noticed a slight 'pause' on pressing the start button if the engine is...

Just curious if anyone might know what'd cause this? Speedo working fine but mileage not increasing with use. Bike is a 2002 gen1 facelift. Ta :)

Hi guys can anyone help my tuono 1000 as suddenly started to cut out and displays ecu on the screen. Anyone help.

Hi all please can anyone help. I have just bought a caponord 2004 with 24000 miles on the clock. The bike runs sweet most of the time untill you open it up the I seems to cough a few times then pull ok. Doing motorway speeds very smooth with the occasonal cough but push it toward three figures...

put a new speedo senser on and took the back end plastics off to get some rails off that used to hold a back luggage box put it all back together and went for a spin speedo worked fine as did every thing else after about 5 minutes the clocks went out no indicaters in fact no electrics at all...

Hi all, I have a 2004 rsv and love it. I went out on it at the weekend and on my way home the bike started run on 1 cylinder. I serviced it the night before without any problems. Is there anything I need to look out for fault wise? I assume its either a faulty plug lead or cap but thought I'd...

Hi Guys. I ride a 2008 RSV Factory. Had some battery problems, bought a new battery and replaced the old one. Switched on the bike everything still fine, press starter switch and everything went dead. checked all the fuses, they are fine. Bike is fitted with a bazzaz system. Please help!!

Rode the bike to work yesterday and throttle cut slightly then my dash went blank and the bike died and engine stopped. Had the bike recovered to home and today i have just taken the seat off to do some investigation and after moving around the solenoid relay and loom feeding the right side of...

My 2004 Tuono tachometer is normally a couple thousand rpm over the actual. At times it is more and times it is less but rarely close to the actual. In any case it is never consistent with the previous time I started the engine. Any thoughts on the source of the problem and a possible fix...

Apologies for the double post - also posted in Mille section - but occurred to me that the fork on my 2003 Mille R (radial brakes) is like the ones on the 1000Rs Hi, I've just had my fork seals done and when I got the bike back from the shop it felt absolutely horrible! I set about adjusting...

Hi All, This is my first post on the forum, i took delivery of my first Aprilia Tuono 1000r about a month ago and love it, after having jap inline fours the Vtwin is a all new beast. Iv covered about 800 miles on her so far and yesterday on the way back from a long ride out i started to notice...

Hi guys, my bike is unfortunately kept outside and all through the winter in the damp and cold she was a bitch to start. The bike is on a optimate but even this afternoon in the sunshine she flooded again. I have cleaned the plugs and the battery is charged but no go. Do you guys use the fast...

Hi folks, not been on here for ages as I've been too busy to ride the bike. It's been sat since April last year and hasn't turned a wheel or been started since then. I had a new battery fitted last year in February and then put the bike off the road and declared SORN on it as I knew I would have...

Hi all, Had a bit of a nightmare with the bike starting over the weekend and looking for some advice. Here is how it come about. Took the bike up to Brands Hatch on the Friday and parked her up outside the hotel in the evening. Saturday morning went to start it and it wouldn't fire up...

Hi guys, what i thought would be an easy job is now a nightmare! one of two screws holding my seat just keeps turning no matter how long i turn the nut! i am stuck on any ideas how to get it out as there is no access to hole other than drilling it out and re-tapping the hole! any ideas??

hi guys ,has anyone got pics of the jet mod that needs doing ? .ive played around with the clutch lever but not much help there , also been told the 08 model comes with the mod already done ?? if this is true then why the hell have i got the problem then :( . my old gen 1 clutch is perfect...

Recently, when the weather is damp my mille takes ages to start. once it has started I can go out and leave it for a few hours and it starts properly. Last week i went to work after having a hard time starting. 9 hrs later it would not start. I gave it full throttle and after about 30 seconds of...

Hia again guys - Having a 'mare with my front brake. Riding home from work Friday, bike slowed down despite me applying throttle.... Only lasted around 10 seconds, then bike was off again... Happy days I thought. Wrong. On the way to work today, bike did the same thing. Stopped and got off and...