R
redratbike
Guest
yep..m6 i've used stainless so no nasty rust:thumbup
now i can show off my hooked airbox!!!!
- Thread starter redratbike
- Start date
-
- Tags
- airbox airbox!!!! hooked show
Help Support Aprilia Forum:
L
lees rsv
Guest
s/steel its a must
H
hooked
Guest
Mark,
Looks like you have been a busy man :thumbup
I think this is another good idea you've had. If i had the time or a lath i would have a go but i am way to busy with work and Air filter kits.
Please Please put me down for a full set :inlove great idea mate :biggrin
Looks like you have been a busy man :thumbup
I think this is another good idea you've had. If i had the time or a lath i would have a go but i am way to busy with work and Air filter kits.
Please Please put me down for a full set :inlove great idea mate :biggrin
R
redratbike
Guest
Mark,
Looks like you have been a busy man :thumbup
I think this is another good idea you've had. If i had the time or a lath i would have a go but i am way to busy with work and Air filter kits.
Please Please put me down for a full set :inlove great idea mate :biggrin
Not a problem at all sir!..have a waiting list already :thumbup
R
redratbike
Guest
Gents,
I 've ordered a load of stuff to make these up...obviously the post is up the spout with the strikes etc so as soon as these turn up and i make some more are i'll be in touch with all who have p.m. me and i'll put a thread in the for sale section:thumbup
A
amb67
Guest
I may have missed the for sale post, been busy recently!
Just looked in my PM folders and can't see that I sent you one, don't suppose you have any seat and tank pins left?
Just looked in my PM folders and can't see that I sent you one, don't suppose you have any seat and tank pins left?
R
redratbike
Guest
Hi Alan,life has taken over recently(wife,kid,school xmas fayre..etc etc),,,hoping to get in the father-in-laws workshop this week...:thumbup
i've got 100 pins turned down...so 50 pairs waiting to be drilled...just had a little drilling jig made so each one is ok...have all the bits to make the retaining cables..will repost later this week on progress
A
amb67
Guest
No rush mate, was just checking I hadn't missed out. :thumbup
Missed you last Sunday, what was your excuse for not getting a good soaking? :nana
Missed you last Sunday, what was your excuse for not getting a good soaking? :nana
R
redratbike
Guest
Gents,
these are ready to go check out the for sale section
http://www.rsvzone.com/forums/showthread.php?t=12589
thanks Mark
these are ready to go check out the for sale section
http://www.rsvzone.com/forums/showthread.php?t=12589
thanks Mark
A
amb67
Guest
Ordered the seat set. :doug
R
redratbike
Guest
if anybody has any pics of seat/tank pins purchased from me please post ..it would be much appreciated:thumbup...like wise any advice how they could be improved ..let me know
R
redratbike
Guest
bump:thumbup
any news on your fitted pins gents..can i improve them?
any news on your fitted pins gents..can i improve them?
P
pieman
Guest
Will post as soon as they're fitted!!
- Joined
- Nov 1, 2008
- Messages
- 628
- Location
- Not far from you!
Snap!
Looks good Redneck :thumbup
I would do the same to mine but on the 04> the side panel screws into the tank, Mmmm got me thinking!
M
monty38
Guest
Quick release pins seat and tank
Saw them while trawling the zone, bought them sunday, delivered on tuesday,
fitted tuesday afternoon, bit of a fiddle on the tank pins, the tank profile on my 03 is different to that shown on the thread but got over it. Will post pics when figured out how.
Many thanks redratbike, top notch cracking idea:thumbup
regards
martyn
Saw them while trawling the zone, bought them sunday, delivered on tuesday,
fitted tuesday afternoon, bit of a fiddle on the tank pins, the tank profile on my 03 is different to that shown on the thread but got over it. Will post pics when figured out how.
Many thanks redratbike, top notch cracking idea:thumbup
regards
martyn
R
redratbike
Guest
i've got some smaller R-pins/clips would that help?
M
monty38
Guest
No need alls cool;
cheers!!!
cheers!!!
R
redratbike
Guest
nice one :thumbup:biggrin
R
redratbike
Guest
Quick Release Seat Pins
basic fitting instructions
Remove your seat and using the original bolts screw these as far as they will possibly go..this cleans up the thread ready for the seat pins.
Lay the seat on take a measurement from frame to top of seat plastic….then assemble the pin with the nut first, retaining lead and star washer , you should be able to set the rough height required using the previous measurement. Remembering to factor in the height of the black rubber washer if you wish to use this.
Quick Release Tank Pins
This is pretty much the same as above but getting the pin height needs to be more precise. Too high and the tank wont go down too low and you cannot insert the R-pin.
You may have to remove the steel inserts in the rubbers and reinsert once the tank has been lowered into position.
basic fitting instructions
Remove your seat and using the original bolts screw these as far as they will possibly go..this cleans up the thread ready for the seat pins.
Lay the seat on take a measurement from frame to top of seat plastic….then assemble the pin with the nut first, retaining lead and star washer , you should be able to set the rough height required using the previous measurement. Remembering to factor in the height of the black rubber washer if you wish to use this.
Quick Release Tank Pins
This is pretty much the same as above but getting the pin height needs to be more precise. Too high and the tank wont go down too low and you cannot insert the R-pin.
You may have to remove the steel inserts in the rubbers and reinsert once the tank has been lowered into position.
A
A303
Guest
Another thing is that I had a right fiddle to get the seat pins holes in a position where I could remove and replace the R clips easily due to them fouling the seat brackets - used smaller clips in the end. Still a top job though Mark, thanks:thumbup
