throttle

The two hoses that come off the throttle bodies to the clutch has a red connector in one of the hoses. Can someone tell me what direction the arrow on that connector should be facing? Towards the throttle bodies or away? Cheers

Hi Guys Looking to fit some 57mm throttle bodies to my gen 1 T racing , can any body advise ? is this a bolt on mod or is there more involved. Looking to try and pull more power from the bike . any tips of all of you guys would be greatly appreciated , still finding my way around the...

Hi Guy's, I've been having issue's with my 04 Tuoldo. 1st is when i drop off the throttle the rev's stay on slightly and come down slowly, so i dont get the engine braking im used to and its a pain to try and change gear, as soon as i let the clutch out the bike pulls forward. What i have...

dose anyone have a spare throttle tube to fit an 04 gen one tuono

How do I do this myself? What equipment is needed? Thanks Mike

Just had a grueling few hours down the garage. Ive been working on the quick action throttle mod for the gen 1 mille. I finally got the cam to run smoothly and return to the stop as it should, adjusted the cables at the TB's, angled the throttle so as it would return at any bar angle then began...

I have 57mm TB's on an O1 RSVR (Gen 1 ) with hooked airbox and dual sided system - chip to match . The chip is twin map.... Map 2 I intend setting 3.5% ( track use only) Is there any merit in using a different value for the equivalent Map 1 ( wet tune, again, track use only )...? Grtzz....!

Nearly got through the winter servicing - new fork oil, oil /filters (nice of K&N to list the same filter for all models)/air filters, replaced the brake fluid and have got as far as balancing the throttle bodies. Does it need to be done with an Axone or does it just need an Exhaust Gas...

Hi, I have been doing some investigation regards adjusting my idle speed out with the ecu and have read about screwing out this bypass screw so as to slightly increase the idle speed, so question is could someone tell me if on this parts diagram the bypass screws are marked no 2...

Which route do the throttle cables take to get round the ignition barrel etc. I,m struggling with this. Do they go behind, in front or what. Help. Please.:confused

Hi Just bought an '03 RSV Gen 2 Factory track bike as didn't fancy risking the '07 Tuono R on track days - o.k. that doesn't make a lot of sense as there probably worth about the same - always fancied a factory so maybe my heart over-ruled my head on this one. The RSV had a spot of...

FOR SALE AND UNUSED BY ME AS NOW SELLING BIKE A COMMON MOD TO BE USED WITH A POWER COMMANDER ETC £100 Based in Sheffield but travel to North yorks to work and can drop inbetween

hello, I have a 04 rsv 1000r and i've got a problem with it stalling... What it does is when I'm in neutral and standing still if i blip the throttle to about 3000rpm and then let go of the throttle, it stalls. Also, when approaching a traffic light, I pull in the clutch for the last 2-3 secs...

hello im trying to balance my throttle bodies with a carbtune but cant get them to match rear seems good but front is a bit low and dosnt seem very stable has anyone had the same problem ?

Looking at the service manuals you need to drain the tank of fuel before being able to remove the fuel delivery pipe? Any way around that or a link to a guide somewhere?

Set of 57mm's with adaptors to fit to Gen 1 Mille's and relevant hoses all blocked off.............ready to fit!! £150 + post

I've got excessive play in my throttle and it's getting a bit snatchy around at low speed. What's the best way of adjusting and any tips?

Chaps Anyone got a throttle cable up for grabs, its the throttle opening cable i need (the one with the adjuster on the darker metal neck) before i have to get ripped off by an official dealer. Rob

Ok peeps while changing the plugs I saw this on the Throttle butterflies and wondered if any of you know what it means?? https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc7/64155_2866146367941_1088235929_32207365_483897112_n.jpg

so saturday my throttle tube gave out and i had a ride to tombstone az planned with my m.c. havent been on any spirited rides or been to tombstone ( on the rsv) so i really wanted to go.. i took a tube off my cbr and started cutting it up... destroyed it... it was late and i did a no no.. used...