fitting

Hi guys, I am in the process of fitting Samco Silicone Hoses to my 2007 RSVR. Unfortunately, family differences mean that my mechanic Brother in law is now not standing over my shoulder as he was when I took the hoses off. I am at the point that I need to reconnect the hoses under the throttle...

Chaps, just a quick q. On the 51s theres a pipe on each side that slips onto a spigot. These are both on the port nearest the seat at either side. When looking at the 57s the left hand side fits fine where it did before. On the other side there are 2 large spigots that are blocked off with large...

Shock listing

How do chaps, I just got some lovely new levers for my 2007 rsv, £39 from fleabay and they look and feel like quality despite coming from China. I just need some advice about fitting them. I had a quick go at the front brake and managed to get the original off, however I don't seem to be able to...

Hi Guys, Fitting a hooked kit to my 2006 Gen 2. Does the foam stuck to the bottom of the tank need to come off ? sure I read about removing it with a hairdryer but cant find the bloody thread now. Cheers :confused

any ideas on how this fits on,got it with the bike be aswell to stick it on,i think it goes on bottom yolk somehow not sure which way it faces or if there is any special bolts clips it needs to fix on.. thanks:dowhat

Hi, Anyone fitted biketek crash bungs? I'll pot pics of set later. Cheers

After rebuilding my bike up after the winter strip ive got one bit left i cannot work out how it came off the bike. Its the small curved piece that slots up the back of the link pipe of the exhaust system. it locates at the bottom with 2 slots and 2 bolts but im struggling with the upper part of...

Oh yes, these are reet dandy :thumbup But the destructions are **** :thumbdown Take your BACK wheel off and bits and bobs And clean everywhere nicely Put this rascal on This bit, the lifter plates go here Then put the little counter holders on and whip them up together...

Awright loons.. splashed oot oan a full set o they sexy R&G crash protectors, Front upper set rear lower set Front fork set So ah thought ah wid pit doon how it went in fitting them and a couple o wee pointers ah found fur any one else thinkin o fitting them. First prob!.. the...

Awright loons, just splashed oot, at long last, oan a full set R&G crash protectors. Any feedback, probs tae watch oot fur or difficulties in fitting said doodahs that ah should ken aboot before startin? (which ah wull dae as soon as they actually arrive!) Cheers bwanas:thumbup

Nuff said ;)

Hi guys, I'm on the Market for a Mille, and have found a R version that looks good. Ideally though, I would like to be able to take pillions, and this obviously would not be possible with the R versions single seat unit! If I was to buy a subframe from a pillion seated bike, plus the seat and...

I have some new Oxford heated grips to fit on my Gen2 10 plate T:D Connecting direct to the battery seems fairly simple with a nice little on/off switch that controls heat level as well I am confident that I can do this my self:) My problem is that I do not like the idea of connecting...

anybody have any tips how to get the bloody thing in?....took me ten mins to get one out and now i can't get the fooker back in....been trying for 3 hours. looks like i'll have to removed the cylinder head pipes i suppose but the bolts look a right ball ache to get to.:angry:angry:angry think i...

Finally got round to installing my kit today and thought I'd write this guide as some have asked how easy/difficult it is. As well as the dipped beam I also replaced the standard side light with an ultra blue one so as to take away the yellow glow from the side light when in normal operation...

Got myself an MPL clutch slave directly from Germany, putting RSVZONE in the subject header! Thanks!:thumbup Firstly - I know there are loads of people on the forum that have already fitted a new clutch slave cylinder, so this isnt intended to teach anyone to suck eggs!! Just thought I'd take...

I bought a tank of E bay and wanted to fit it to mine but it is slightly different. The tank has a fixing in it to take a panel but I dont know which panels are needed. I have got some photos This is what I have at the moment and below is the tank I want to fit so if anyone has either...

i'm expecting to take delivery of a dr rossi chip in the next couple of days...been doing a bit of research on fitting and i'm wondering about the part where i set the tps sensor position. i know you have to wind the idle screw out....is that so its fully open so idling as fast as poss or as...

if i fit my power commander 3 and run it with a zero map does that just run the std fuel mapping or does it run what ever fuel map thats being sent from the chip/eprom? i have my pc3 which i can fit but i still have a few more mods i'd like to get out of the way before i get a custom map. was...