fitting

Hi All I'm probably just being thick, but I have just tried to fit a US sidestand and the bracket is different! Mine (an Australian model, but I think the same as UK/Eur) has two bolt holes whereas the US bracket has three. It looks like the lower engine mount bolt would fit but I can't see...

thought this may come in handy :thumbup http://www.oberon-performance.com/acatalog/Aprilia_Clutch_Slave_Cylinder_Instructions.pdf

Hey guys, I have just purchased a new set of HT Leads from Magnecor for my '02 RSV. Gone to fit them this morning and have found that there are no connectors on the coil end of the leads. When removing the originals it appeared that they had no brass connectors which hold them in the coil...

Abba fitting kit for Gen 2 Tuono/RSV like new £15 delivered. PM if any takers.

Hi guys. 1st post even though I have had my T for three years! I have got hold of some used Aprilia Performance rearsets. Does anybody have any instructions on how to fit them? Left side is easy but I am cautious about the right side relocating the rear brake master cyclinder etc...

Guys, I'm after some advice here...... I have started the fitting of the new r&r and have the furukawa connections all crimped and soldered and ready to fit to the bike, but..... I am after some advice on the existing wiring connections... Basically, I have the two connectors fitted to the...

Hi all Does anyone know of a mobile tyre fitting service that covers Herts Appreciate any help cheers

Is it safe to just remove the plug at the rear of the clocks or should the battery be disconnected?? Cheers Andi

Hi all,will be fitting another engine in the next couple of days and was wondering if there are any pit fails that i will need to avoid.The bike is a 05 model,it's a straight swap no clutch or any other parts to exchange.(trackdays why do we do them) The engine that is coming out still...

Help needed chaps Fitting a new mpl clutch slave to 01 rsvr. I've read all the previous threads (I think) and have fitted the slave, I bought a bleeder and revearse bled from the nipple loads of times. (forced fluid in from the slave) Still the lever comes to the bar with no bite. Tried the...

Hi Guys I just bought a Ventura rack and L Brackets for my Gen 2 RSV Factory (From ebay) I can work out the basics of fitting it from the video but it says read the instructions carefully (which I don't have). Just so I don't miss anything, has anybody got a copy of the instructions for the Gen...

Hi all, got myself a bit of a problem. when fitting a new jet 40 to get rid of my inability to select nuetral on my 05 RSV R, we over tightened the cover bolt and stripped the thread out from the casing, think it's the crank case?? now the cover bolt doesn't tighten up properly and oil is...

Have acquired a pair of Gilles Vario Clip-ons and keen to get them fitted (2003 RSV Mille R). As well as being clamped to the forks I notice the standard bars also bolt to the underside of the top yoke. The Gilles bars don't appear to bolt to the yoke, is this right - will the bars be OK just...

Hi there iv bought i rossi chip came with instructions today im gonna fit chip tomoro it says set the by-passes screws to 2.5 front and 2- 1.5 rear and co trimmers were about are these screws located. iv read on or two posts that dosent say anything about these screws just trimmers could do with...

Hi ive recently bought a second hand power commander for a 2008 rsv 1000r does anyone have a copy of the fitting instructions many thanks puffer.

Got this new at Xmas and never used it because I had to sell my bike and do not see myself getting another for a while (can prove purchase with receipt). It is taking up space at the minute so i'd rather sell it and buy another when I get a bike in the future. If your local this will be a...

Hi all Just brought a set of Gilles rear sets for my 2006 RSV1000R and was wondering if anyone had a fitting guide or some decent photos of some filled? The actual process of bolting them on is clearly pretty strait forward, but on the gear lever side do I need to cut away the plastic faring...

Got a set of led flashers as broke my rear left indy when the bike fell over. Now the bulbs in em are 10watt jobbies, so if I replace the front stock flasher with a 21watt jobbie will the it work ok with the stock relay as doubling up on the bulb wattage on the front should in theory keep the...

Guys, I've managed to find a set of 57's from an'07 Tuono for my '02 Mille. Just a quick check to find out what's all involved in fitting them? What are the differences? Mark (Tash) should be able to sort me out with all the relevant bits but just trying to work out what all the differences are...