fitting

Hi guys, quick query. Going to fit Fuel exhausts to my Gen 2. Will they literally slip on or will I need some sealant too? Cheers. Sent from my iPad using Tapatalk

Hi I’m wanting to hardwire my Satnav to my 2014 Caponord. I know there is a Satnav wire behind the dash. Is it a green & blue wire with a black plastic connector? I’ve got a photo of it but not sure how to upload it. Thanks

Hi All, I am trying to get the fitting kit for my Givi Tanklock bag. There does not seem to be a specific kit for the Gen 1, Is it generic to the Mille, Falco? Are they all the same Fuel cap? Cheers Barks

I'm after fitting a single projector headlight to my RSV race fairing, like the one on the NSR500 highlighted below, the projector light unit is recessed (french'd) into the fairing sorry about the pic but I think it is just visible. The owner of this bike is in the States at the mo so I can't...

Hello guys. After doing an oil and fliter change on my 02 Mille I was slightly conserned how the new filter went in. I have replaced with an K&N - 152 (short style filter) The push fit wasnt very reassuring and it just sort of sat there loose. Before putting the cover back on it was very easy to...

Hi guys would anyone be able to tell me the fitting used to route the breather through the hooked airbox plate and for a breather filter in it. It looks like it similar to a self seal breather take off (picture below)but needs to be a male male connection to fit pipe either side. I have a...

Hi all I have an Abba stand and want to make a kit for my 2010 Tuono. Does anyone have a set and can send me the dimensions please so I can make a set? Sent from my Nexus 6P using Tapatalk

Hi! Does anyone know will Aprilia RSV Mille ( year 2005) fuel tank fit streight to year 2008 Aprilia RSVR factory? I think it will fit. :jack Plan is to buy other fairings and fuel tank for track days..

Just wondering if anyone has had a similar problem where the water temp runs hotter after fitting a rad guard? I have a new Factory 1100 Tuono which has an Evotech rad guard fitted. Prior to fitting the guard it was rare to see the water temperature up to 100C whilst actually moving it does get...

Quick vid of fitting a Sigma Slipper Clutch on a Gen1 RSVR all comments welcome All seems to work fine tho not had it on track yet to see what it's like under hard riding conditions, fingers crossed. Thanks to all I asked for help before fitting. Not a daunting job at all...

I just got me a smoking deal on a pair of Pirelli Super Corsa SPs, but I'm not so sure if the 200/55 rear tire I got would fit on my 2002 Mille R. Has anyone tried it? I currently have Dunlop GPs 190/55 on the rear and there's very little clearance between it and the chain.

Little vid of mine to show it's not a tricky job at all :thumbup https://www.youtube.com/watch?v=5R9MkwkUeos&list=UUC2keDDB8gFQutnG2anLvnA

Hello again everyone. I'm indeed of some technical help here. Im fitting a new disc brake and I'm asking if need to fit this at a specific torq? Or shall i just tighten the mother out of it?

Morning all, I have just been lucky enough to score a Ventura luggage system for my 2007 RSV, however it seems that there is one minor fly in the ointment, and that is the fact that I have no fitting instructions, and my initial trawl of the internet has proved fruitless, even Ventura themselves...

Hi, ive just bought some NGK's for my Tuono and plan to put them in even though its got full service history as I find that you never know if they were replaced until you check.... so I may aswell just bang some new ones in... especially as DCPR9E were only £2.50 each on fleabay. Question is...

Greetings All. Just posting in the new members area and already need to ask for help! Fairly familiar with the RSVs as I have had a couple of RSV Mille bikes and now on my first Tuono - superb bike and luvin the higher bars! My Tuono is a Gen 1 2004 model. On my last RSV Mille (2003) I...

Anyone have any problems fitting an Austin Racing GPR2 slip on, the austin down pipe is bigger dis than the OEM pipe at the end of the bellypan, thought it should fit into this but fits over i, any ideas?

Afternoon all, Not being afraid to undertake any form of mechanical works, having built two kitcars and rebuilt my Yamaha Vmax, I have never split an old chain and fitted a new. Now whilst I understand the process, I am hesitant that this is one component that you don't want to fail...

Right got the bike back and now after replacing the metal tank with a plastic one the sides do not fit ! The bike is a gen 1 do i need the get 2 mesh side covers? Jason

has any one fitted or got installation instruction for the gear lever version qs? hope some one can help