brake

Folks, Would be much obliged if anyone can advise on the bolt size (mm diameter + length) for a standard 2003 model (2004 plate) Tuono for: - Front callipers: - Rear calliper: Planning to replace rusting originals with stainless bolts. Thanks in advance.

Having owned a mille and knowing how much I liked the feel of the front brake setup. I decided I'd change the front brake on my speed triple to the brembo master cylinder fitted to millie's Ordered a good condition used spare from ebay and a replacement lever from M&P as the ebay master cylinder...

I have got a few sets of 4 Racing reservoir caps on offer, they are £35 pair including delivery, pm me if interested. Cheers Mark

I have got a few sets of 4 Racing reservoir caps on offer, they are £35 pair including delivery, pm me if interested. Cheers Mark

Hi, just wondering if someone could tell me the diameter of the piston in the front master cylinder. Thanks Jeff

Hi all I am trying to push the rear brake pistons back but I am struggling to get them both back when one goes back the other pops back out. One of the plastic inner parts has also broke with my efforts will this be a problem long term. Both pistons move but I can't get them both out far enough...

Im going to service my gen 2 over the dark and dismal winter months . one of the jobs is front brake pad replacement , just wondered what opinions or preferences and experiences you bods out there have got . I would ideally like brembo pads but they are a bit on the pricey side (...

I have a pair of Genuine Aprilia Tuono front discs. Part number AP8113296 £350 include postage.

Hi, I need new brake pads for a 2006 RSVR with Ohlins forks and Brembo brakes. At most I need fast road type pads, certainly nothing approaching race standard for my abilities. I don't have a lot of spare cash to say the least right now and need to get the bike through an MOT. Any bargains you...

Just bought a bike from Paul W yesterday - top bloke and definitely a good source of spares, except for what I'm looking for here! I need a front brake lever - specifically the little pin that actuates the master cylinder (sorry, don't know what it's called), and a rear seat hump off an 03/04...

Wanted short leavers for rsv gen 1 (2002) So went on flee bay and brought these Read all item description and said fits 2002 millie. To my surprise only fits clutch side... I have this on my millie ( understand when fitting new ones have to undo little screw on leaver.. Etc) Take it...

Im fed up bleeding the dam thing every mot for it to last 2 hrs ... Cant modulate wheelies but i would rather not throw £300 for rearsets . Has anyone tried using a right hand set from a different bike that has the brake lever already mounted in the correct position . Im sure there cant be...

ARRGGHHHHHHHH. and GRRRRRRRRRR. The new levers feel lovely.... really impressed. Took the bike into the office today.. Got about 5 miles and going down the lanes I thought the bike had died as I had no power at all.... ???? Pulled over and the brakes were locked solid. I then noticed that...

hi all real scary moment to day going round a long left turn and the rear brake locked on its only the look of god I stayed on back pads melted disc is blue and now warped no fluid leak so hope the calliper seals and master cylinder seals are ok I are at a loss what caused it all I can think of...

Hi guy s got an 2011 rsv4 the brake light has started staying any idea s on how to check wot the problem may be or how to rectify it ??

hi i have a 2008 rsvr factory . my rear brake stopped working as i think its a common fault so i replaced the brake fluid got it working again then i got some heat resistant rubber tube split it in half from top to bottom placed it between the engine and the bottom of the brake tube to the top...

Hello I am after a very cheap or free front brake disc from a rsv1000 2001-2008 I am not after something mint, i just need it to mock up the front end on my bike before i splash out on new discs for the bike I can collect in the london area if that helps Thanks

Hello again everyone. I'm indeed of some technical help here. Im fitting a new disc brake and I'm asking if need to fit this at a specific torq? Or shall i just tighten the mother out of it?

Hi guys, I was wondering if you can help me out explaining what happened to my brake. I was just riding along noticing a decrease in power (which I now realize would have been the brakes biting without me using them) I accelerated through the power slump and a minute later the rear brake...

So I just bought an 01 Mille yesterday and I can't seem to get the rear brake to work. I've bleed the line about a million times, pulled and split the rear caliper to check the pistons and o-rings. I unbolted the master cylinder to check for leaks and I've come up clueless. I'm not losing...