- Joined
- Feb 28, 2011
- Messages
- 213
- Location
- Oxford
Ooooooh yeah!
Next on list is levers and tail tidy when I find some.
Next on list is levers and tail tidy when I find some.
Exhaust??
- Thread starter Barking Spider
- Start date
Help Support Aprilia Forum:
- Joined
- Oct 6, 2010
- Messages
- 2,501
- Location
- Bristol
Tail tidy (& small plate) is a MUST - get 'em cheap as chips on ebay.
Levers - either go for the established players: ASV, CRG (like what I have), Pazzo etc, or take your chances with the fiendish Chinese copies on the 'bay. I suspect they're probably ok for the money.
Levers - either go for the established players: ASV, CRG (like what I have), Pazzo etc, or take your chances with the fiendish Chinese copies on the 'bay. I suspect they're probably ok for the money.
- Joined
- Feb 28, 2011
- Messages
- 213
- Location
- Oxford
Is there somewhere that sells all the key players so I can compare them? Don't want Chinese copies, made that mistake before - s.h.i.t
- Joined
- Feb 28, 2011
- Messages
- 213
- Location
- Oxford
I've got a video now, the sound quality isn't great because I was using my phone. Problem I got is, I can't get my phone to load it onto YouTube, any ideas?
- Joined
- May 26, 2009
- Messages
- 78
- Location
- Preston, Lancs
No idea about the video mate - but how's the bike idleing with the new exhausts?
Mine seems a bit lumpy; and maybe a wee bit snatchy rolling back on the throttle..
Mine seems a bit lumpy; and maybe a wee bit snatchy rolling back on the throttle..
- Joined
- Feb 28, 2011
- Messages
- 213
- Location
- Oxford
Yeah mine was, cured it by doing about 60 miles with the baffles in, then the same again with the baffles out then just had the idle speed picked up a touched so it was back where it needed to be.
A power commander is on the cards soon so after the dyno run to set it up I'll see what improvements the can has made.
- Joined
- Feb 28, 2011
- Messages
- 213
- Location
- Oxford
Oh and make sure the bike fuel map is on "race map 2". You'll need a dealer to change that for you, should cost about £20.
- Joined
- Jun 3, 2011
- Messages
- 1,242
- Location
- Near Welshpool
I just had a PC fitted to mine & Dyno run with custom maps after fitting new cans. smoothed out the lumpyness, now really smooth.
- Joined
- Feb 28, 2011
- Messages
- 213
- Location
- Oxford
Glad to hear that as £300+ needs to be money well spent for fear of much inflicted pain from woman in doors!
- Joined
- Oct 5, 2008
- Messages
- 444
- Location
- Lincoln, UK
It's good to see folk going for something different! :thumbup
I bought a pair of stubbies off ebay (from a z1000) for £100 and thought they were Scorpion but after a lot of research have discovered that they're probably MTC GP Pro's. They have crappy little baffles in but might as well not be there! They're bloody loud and pop/crack on the over-run, which I love. I've recently fitted 57mm tb's and already have a PC3, so next week I'm getting valve clearances done, tb/co2 setup and an advance map done. Hope fully it's going to run beautifully after that! :yes
I bought a pair of stubbies off ebay (from a z1000) for £100 and thought they were Scorpion but after a lot of research have discovered that they're probably MTC GP Pro's. They have crappy little baffles in but might as well not be there! They're bloody loud and pop/crack on the over-run, which I love. I've recently fitted 57mm tb's and already have a PC3, so next week I'm getting valve clearances done, tb/co2 setup and an advance map done. Hope fully it's going to run beautifully after that! :yes
Similar threads
- sharpei23
- Aprilia RSVR
