today

Just off to the BMF on my V4 today, will be looking out for other Tuonos whilst there as we are far to thin on the ground it seems. A few of my mates will be on their KTM 1290 SDrs with Stubby AR Cans on so you will no doubt hear us before you see us! Rob

Hi all, My names Steve. Literally just got home from picking up a 2001 Mille R. Just under 13k on the clocks. Carbon everything, Sato rearsets, Akra full race system. I believe looking at the tank stops (they are slightly lifted from the frame) that it may have had the airbox mod done. Clutch...

RENNTEC CARRIER / RACK BLACK APRILIA RSV1000 TUONO (07-) used | eBay

Off to see Griff to set up in Feb will get the dyno results up later :thumbup Modded exhaust (redratbikes) Gabro F255 Chip Hooked air box PC3 Titanium RSV can The standard ones I'm holding. Looking forward to the results. Lots of fun for Aragon in May :thumbup Will vid dyno runs for you all to...

Had a nice ride out to squires today with phatcat.. good to meet up... roll on the next one .. :)

Parking up today: backed into a space, put side stand fully down, dismounted and down she goes :banghead Managed to wedge my left leg and arm under the bike and luckily got away with only a scuffed bar weight and bent clutch lever (and a twisted knee). :bawling:bawling. All it took was a 3...

Set the kin alarm off again ,started bolting on the air tubes I got from James Played Tomas the tank engine with Alfie , my grandson ,watched wifey cut the grass , had an hours kip after that ,with wifey ,drank some cider ate some olives A Good day What did you do Mike

First ride for a while, so had a nice bimble around the dales: Stopped for a breather at Grimwith Rez: Admired the view near Hebden: Notice a large gathering at a pub near Skipton: Lots of old beastie cars: And this minter: Only stayed "local"..... but fantastic to...

SO having been fighting the beast to rude health for 6 months, its sell it or love it. LOVE IT sooooooooooooooooo first upgrade K&N from ebay for £20!! What next gang, link pipe mod? :cheers

Whoever you were ripping around, the Ape was a credit to you; looked and sounded absolutely ACE.........and the riding wasn`t half-bad either ! :thumbup Just before you came on (or before I saw you anyway) there was a nice-sounding crossplane R1 motoring around as well (he was quick too), and I...

... been checking all the forums and there seemed to be a question regarding a rev limiter during the break in period, even dealers were confused. Vin # 126 had an rev limiter and there was no menu function, even in dealer mode, to remove it. The bike would not rev past +/- 7500 rpm. Today...

As above, I was riding up Kielder in Northumberland today and spotted 2 rsvs on seperate occassions. First was on the Kielder road and it was a Grey RSV mille Gen 1 same as mine and the second was a black RSVr Gen 2 just before chollerford??? Regards Dave

Anyone watch it ? Shocking conditions, Grinner got another bum deal, so did Chaz, nice to see Guinters get a top pod, what the frig has BMW gotta do to get a win. Hoorah for Jonny, what a save btw, and a bigger Hoorah for our Ooojean :thumbup Carlos ****** up big time in the second eh, wtf...

got around to fitting the 15 t front sprocket that came with my '10 factory 1000r today.It was under the seat with the "fool kit"Feels like a new bike ,now I can ride slowly down my street without all that jerking around in the lower gears.

Well it's been a rather frustrating 2 months with my bike not turning a wheel due to a knackered fork & repair is at least another 2 weeks away.. Today, i popped down to my local BMW dealer & booked a test ride on a new S1000RR, which up until a few minutes ago i was seriously considering...

At last, the suns out, had an early morning spin to the bike show at Wistanstow, back and did the usual polishing and check over http://i293.photobucket.com/albums/mm78/arriva996/DSC00138.jpg http://i293.photobucket.com/albums/mm78/arriva996/DSC00137.jpg...

http://i293.photobucket.com/albums/mm78/arriva996/DSC00138.jpg http://i293.photobucket.com/albums/mm78/arriva996/DSC00137.jpg http://i293.photobucket.com/albums/mm78/arriva996/DSC00136.jpg

Got my cnc chain adjusters today :( didn't fit as they were for gen2 never mind....... someone will get a bargain they are now in the for sale section....any1 interested?? Any way while I had the back wheel out took apart and cleaned up the renthal sprocket and hub carrier and oe chain adjusters...