gen1

i need to buy or borrow a top yoke from a gen1 rsvr (ohlins forks) i have a machinist standing by to make me a custom top yoke but needs an original one to get measurements from. overall condition not important as will only be used for measuring

Hi, I have for sale a 2003 rear seat fairing in Tulip red. Removed from my tuono as I have replaced with a CF fairing. £80 ono. Buyer can collect or will arrange postage for a additional £8. Thanks for looking. Phil B

Hi guys, Just bought an 02 RSV in the standard matt black, but it has I been in the kitty litter on a track day. There is nothing major, just light scratching etc as had full set of crash bobbins on. I want to make the bike look mint again. Wondered if anyone has a full set of plastics and...

Hi all I would like to swap my red petrol tank for a black one. I would prefer a satin/matt black but gloss would be ok. My tank is 99% perfect, I would want the same back. Anyone interested in a swap ? Cheers, Nick.

Hi guys if see one or are selling one please let me know

Hi all 2003 Gen1 RSV / Tuono conversion Need coil covers and water bottle cover.....pref carbon Help !

Hi Looking for one of the above to fit to my Gen1 Mille. Needs to be 100% straight for a perfect fit :devious PM me if you've got one for sale Cheers Oscar

for sale gen1 carbon numberplate bracket good condition £15 plus postage

I have a left hand headlight that is in brand spanking new condition, with not a scratch on it £150 posted gen1 original screen, it's been kicking around my workshop for quite a few years and is covered in dust, £15 posted gen 1 extended rear mudguard, perfect for the all year...

im looking at fitting an RSV4 seat unit and subframe on my gen 2 so the gen 2 rsvr bits are up for sale Rear subframe complete seat unit with lights and indicators Seat Hump Riders seat undertray for battery etc. . .

I've searched the forum and cant find this info, its really a question about engine mounting points, will the motors swap from frame to frame i.e. will the Gen1 motor fit the gen2 chassis and vice versa, I know there are differences in ancillaries, its just the mounting points I'm interested in...

Ohlins stabilizer $125 Racing exhaust (some small dents and scratches) $95 RSV Mille R clip-ons _ fits only R $100 fuel pump $120 gas tank some small dents and scratches - clean inside, needs paint $175 clutch slave cylinder $55 solo cover $50 side covers $60 front foot brackets pegs $75 right...

Hi guys, i am looking for a set of shotgun exhausts, the Shark ones look cool, but any aftermarket set be nice. Or a mint pair of Aprilia ones. I know they as rare as rocking horse **** but if anyone knows of or sees a set please message Ta muchly Jim

Guys have the following for sale Gen1 98-03 power commander non- USB type but comes with 2 leads serial to serial port and serial to USB port and new 9volt lead to enable map changes off bike. Leads and battery connector just cost £30 so £100 posted Pair gen1 brembo wheels good condition...can...

I am selling my carbon race fairing, this has only been used on my road bike and is in very good condition apart from a couple of small cracks in the resin. This also comes with carbon fiber race air ducts, the retail on this is £980 inc the ducts, looking for £480 inc postage. Cheers Mark

Hi all, I'm after a standard gen1 clutch lever, specifically the small grub screw part that pushes into the rubber flange when you squeeze the lever. Of course I realise I need to buy the whole lever. Managed to snap this part in a fall (don't ask)

Hi time to sell my mint Gen 1 rsv1000r 2000 model I'm 3rd owner first was a good friend who had it for 10 years, 2nd was my best friend and now me. It's truely mint a very well cared for bike. 16000 miles. Titanium aprilla end can. a delvic one and standard. power comnander, map for this bike CD...

I have a sil motor exhaust system for sale its stainless full system including hangers and chip very good condition £ 300 ono

Cant remember where I found this pic, but it is yummy.. Fireblade rear tail.. In desperate need of a tail tidy though..

I have the above Gabro chip for sale. Its best suited to an unmodified gen1 bike. Standard can, header etc. It made the power delivery and fueling feel much smoother I no longer had to clutch it going round.corners in built up areas. Its probably 1yr old. Selling as I have modified a few...