This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

cutting

  1. C

    Rsv4 cutting out

    Hi, I bought an RSV4 (2010) model earlier this year, it's beautiful and has really restored my love of bikes after a few stale years on a gsxr. Even planning to get back on track with it. But - It has randomly cut out on 3 occasions for no reason what so ever, had it back into my dealer who has...
  2. Z

    Please help!Bike cutting out

    Hello Gang,I have an issue with my 2008 RSV.The bike has cut out a few times,it seems to happen when I change gear.The first time was at the bottom of Bray Hill on the Isle of Man as I pulled away from the lights and changed into 2nd.There is still power to the dash with no alarms or side stand...
  3. kimboshmerly

    Help Required - Mille Cutting Out - Broke Down - Possible Fuel Pump??

    Guy's, Can anyone help, any ideas? Whilst out on my bike (2001 Mille RSV - 12,000 mls) yesterday morning, first ride of the year after a good winter service/ overhaul, it simply cut out, dead. I was just simply cruising along, high gear, few rev's and then the engines dies, all electrics and...
  4. R

    Cutting out at high revs!

    Hello guys, I'm very new to this but had mille for a little while and don’t seem to have much luck! Anyways had my first track day today only to brake down after the warm up lap!:doh The problem, cutting out after reaching 6-10k revs and then the revs drop to below 0 and power cuts out to...
  5. M

    2002 RSV Mille R - Occasionally Cutting Out?

    Hi Chaps, I've only owned my bike for about two weeks. I've been out on it about a dozen times, but the last to times the bike has cut out after 10 - 15 minutes of riding. After it has cut out, if I turn the ignition off and on again, the bike starts and I can continue riding. Any ideas...
  6. B

    '00 RSV Mille Nero Stalling/Engine Cutting out when putting into gear... HELP!!! :o(

    Hi Guys, I need a bit of help. Bit of background... Bike is an '00 RSV Mille Nero. Renegade Airbox and Can, with correct MAP through a Dynojet PC III. Bike has had trouble recently with a leaky clutch slave cylinder which has been cured by fitting of an Oberon replacement and properly bleeding...
  7. D

    remap by wire cutting?

    Hi guys, new to milles got 2003 great bike love it,i have been told you can cut a wire under the seat and it will remap for a open system? any advice please. divingbig.
  8. M

    jerky cutting out after start

    Hi everyone, Had an interesting ride to work this morning. I have a 2004 RSVR, here's what happened: Started bike as normal, no problem. After 1/4 mile experienced engine temporarily cutting out-starting-cutting out-starting. Needless to say the jerking around of this was a little unsettling...
  9. B

    2002 rsv keeps cutting out

    hi new to the forum my rsv keeps cutting out on me does anyone no what the problem could be its getting annoying and dangerous
  10. R

    fans not cutting in/running rough/sticky throttle

    started the bike up on sunday after 2 months (yes i have topped it up a couple of times with an optimate) while it was running the temp rose to 105 :eek: and fans didnt cut in..how where do i check wiring throttle not returning ...so i need to investigate that lastly running rough looks like...
  11. AREESSMILL

    Fans not cutting in ffs

    Went for a rideout today and the fecking fans didnt cut in:rant went up to 101 degrees and so i stopped at the side of the raoad to cool down. Does not overheat when running. I had the front fairing off to paint the front is there a connector or something that i forgot to connect or is it...
  12. P

    Bike cutting out

    Hi, I have an RSV1000R 2006 model. I've only had it 5 weeks and because of the **** weather and being away with work only covered 250 miles so in all it's got 8,250 on the clock. I love the bike to bits and I've had no trouble at all except the back lighting on the clocks was intermittent but...
  13. K

    Bike cutting out

    Aaaaaaaaaaaaaaaaaaargh , Bike ran fine for about 20 minutes this morning then coming up to a stop, clutch in to change down bike died. Put into neutral hit the starter and it fired straight back up again. Next stop and it did it again :jack. For the rest of the journey when I came up to a stop I...
  14. M

    cutting a bellyapn

    has anyone chopped up their bellypan to fit akrapovic system,is there a template avaliable. or any pics. cheers murf.
  15. F

    cutting out

    Hi all I had a strange thing the other day I was riding along and the old 2004 tuono cut out efi flashing etc ,I coasted for a bit then hit the starter ,and away she went,any body else had this ,checked battery leads earth mounts charging all seems ok but the only thing the volts metre on the...
  16. J

    Engine cutting out during shifting - ideas?

    I have a few hundred miles on my new 2007.5 Tuono (first service not yet done) and have encountered a problem I was hoping someone out there could help me with. During shifting the engine sometimes dies. This has happened when the engine is running warm and dry. The problem crops up when I am...
  17. P

    Cutting cut @ 6000 rpm

    Mille 02, like hitting rev limiter, no lights or codes on dash split second, happens once or twice a ride, any thoughts??
  18. E

    Radiator fans cutting in early?

    just went for a quick 2up ride to show my bro the new bike, we were out for about ten minutes and made my way back home. We got off the bike and left it running for a minute, the temp rose to 81degrees and the fans cut in. This is early i know because when I picked the bike up I got stuck in...
  19. D

    Cutting out at low revs when cold

    When my bike is cold it has a tendancy to cut out when I am down changing gears i.e coming up to a set of traffic lights down changing from 2nd to 1st. When running nice and warm there isn't an issue, bike runs sweet, it just when it is cold. Any ideas?
  20. S

    Cutting fairing for twin akra pipes

    I have just got hold of a full ti / carbon 2/2 system for my 03 RSVR and would appreciate any advice/guidance on cutting the fairing to accomadate the second pipe before I start to fit it. I don't want to jump in and get it wrong anyone still have the template I could get a copy of please...