working

Just bought a 2013 Capo with 12000 klms and the heated grips don't turn on. Wondering about a fuse. And the A adjustment button that is used to adjust the traction control doesn't have any effect when pushed, thanks

Noob here, Hello everyone, I have recently purchased a 2001 Aprilia Mille. The right side of the dashboard does not function after the initial computer check. During the initial computer check, it shows the coolant temperature and the clock. Almost immediately the coolant temp and clock...

Please can someone help or advise as my fuel gauge is stuck at 4 bars. It's a 2015 model with 3700 miles on the clock. I'm heading to Austria on it in August so ideally would like it working!

Delete this delete

me again..new capo ( 120 mi. ) on the odo... fuel gauge doesn't seem to work...any tricks i'm missing or is it just broken ?

hi i have a 2008 rsvr factory . my rear brake stopped working as i think its a common fault so i replaced the brake fluid got it working again then i got some heat resistant rubber tube split it in half from top to bottom placed it between the engine and the bottom of the brake tube to the top...

Hi all, i have a 2004 rsvr that i picked up on saturday and the speedo and stopped working. anyone else had the same problem? if so how did you go about fixing it?

I finally got my tuono up and running and thought I'd share some pictures, it's a 2007 with only 5300 miles on it. Runs fantastic, just needed a little cosmetic love before getting her back on the road! I had gotten and amazing deal on it because of the recent salvaged title, but looks amazing...

Hi, can someone please help. My main beam was working then all of a sudden it's stopped. It won't flash on the lap timer or won't work via the main beam button. It's showing a blue light on the dash and also making a noise from the relay area. I've checked the fuse and all seems fine. Can't...

Hi All This is my first post after joining today. I have a 2007 tuono factory and the speedo/mileage isn't working, the rest of the clocks and electrics are working fine. Is it the sensor mounted at the rear wheel? Does anybody know what checks I should make before I order a new one...

hi, my shift light on my rsv 2002 does not come on at all ,I have tried resetting to come on at lower revs but still nothing. does anyone know what maybe the problem or how I can remove the clocks to investigate. thanks.

need help, clutch lever spungey . bike starts but put in gear bike wants to move. start to let out stalls engine. also rear brake resivoir fluid goes down .own 2007 tuono factory. Thanks for any info

Don't know where to start with this post... I've a Gen 2 RSV which had a back brake that would not work. The system was taking in air and couldn't be bled. I repalced the rear brake caliper along with the rear brake cylinder and reservoir - The system was flushed for air but for some reason it...

Hi guys, I noticed today that my Main beam is not working whereas the dip is fine. I can hear a 'tick' coming from the relay box. Is it just a matter of getting a new relay or could it be something a bit more complicated? Thanks in advance.

Need help please, turned the key on today and the digital dash display isn't working properly can't read anything on the dash just lines on it the bike still starts and the rev counter etc work but nothing on the digital bit? Any advice would be great thanks

Hi guys, i could do with some help! I am trying to set my TP-0, although my diag wires dont appear to be doing anything. I have removed the right vent pannel, found the 2 disconnected wires, connected them, unscrewed the fast idle, turned on ignition and only standard readings displayed on dash...

Hi reciently i have fitted some wavey discs to my 09 rsv Factory, much to my suprise yesterday the speedo wouldnt work or the mileometer for that matter?? What have i done to it?? all i have done is swap discs and bolts? Any ideas are greatly recieved Ant

just tried to start my 08 tuono and no go ,i noticed the power commander wasnt lighting up so i took it off ,bike started 1st press .do power commanders just stop working can i get it checked out by sending off ,it does light up when you connect the 9v battery though .Anyone fitted a bazzaz unit ?

My indicators light up but dont flash. Im a bit crap with stuff like this, will it be an easy fix?:confused

Hi all I'm new on here so please be gentle!!! I have purchased the other day said bike for a reasonable £1800. Only problem I saw was the main beam/dip would not work on the switch but only with the flash/pass/lap button. So I checked the fuse....ok Switched the 3 relays around to see if it...