wiring

Hi guys, just a quick one. I replaced my APRC only main wiring harness with the APRC + ABS harness (2D000062). The old harness had only one ground wire and the new one has two. Do I need to connect both the ground wires to the terminal forward on the engine block, or just one. Presently both are...

Hi there I run a quick search but nothing showed up. I'm experiencing an issue with my lock wiring. A little while ago all of a sudden mid-riding my instruments started flashing and the bike was turning on and off. I took it to the mechanic and he identified a cable from their lock wiring had...

Hi All, I recently posted regarding the bike getting wet & now sulking. Had a proper look today & found the L/H switch gear totally fried (picture hopefully attached). It looks like I was not far away from a major meltdown (the bike, not me yet). The black shroud covering all the cables was...

hello guy. ive just bought a 2004 rsvr wiring loom with a datatool alarm that i would like to remove and fit on my ducati but am having some problems identifying some of the plugs that the wire trace back to. any help would be good. 20160827_212258_zpspfjcnaps.jpg Photo by fezzo2003 |...

Hi I have recently purchased a syncro tech quick shifter for 2000 rsv mille , on the fitment instructions it says connect the blue wire to ecu control wire on the coil . I cant see any ecu control wire on the coils . If any one could point me in the right direction would be much appreciated.

Hi all,sorry I've not been on in ages, could I pick your brains,I have a Cheap solenoid for my mille while I'm waiting on a replacement to come,but the wires are different to the loom the solenoid I have has Green/red and yellow/red on the loom they are red/white and blue/white what do I connect...

I purchased my bike (2004 RSV1000R Factory) yesterday and was told it had a small issue with the harness. The only code showing was for the oil pressure sensor. I removed all fairings and started looking. The stator and rectifier connectors have been removed and been hard wired. I found a plug...

I need a favour, just replaced my taillight but noticed that the wiring into the connector from the bike side and not the tail light side has come loose and I don't know where it needs to go. There are three points, can anybody take a quick photo if their wiring loom so I can see where to put...

Just been stripping down and cleaning my new to me RSV and noticed this wire under the right hand side of the seat was pulled apart. Didn't look like it had come apart, more pulled apart and tucked away. Any ideas or a link to a wiring diagram please?

Has any body out there got a readable wiring diagram for a gen 2 tuono . ive got 2 off on my pc but neither of them are readable when zoomed in , ive got a 3rd one that is readable but is for a us spec which has a sligtley different loom, so not much use !! pm me and I,l send u my mail...

Greetings All. Just posting in the new members area and already need to ask for help! Fairly familiar with the RSVs as I have had a couple of RSV Mille bikes and now on my first Tuono - superb bike and luvin the higher bars! My Tuono is a Gen 1 2004 model. On my last RSV Mille (2003) I...

Here ya go

Just a heads-up on the fail mode I just experienced. The boot anchoring the wires to my ignition switch had cracked/failed. Upshot was the wires were flexing too much with the turn of the yoke. Eventually this caused a break at a solder connection in the switch. In my case it was power to the...

New bike only had it a week... Bike isn't charging, I've done all the tests with a multimeter, I think I know what to do, BUT the wiring is melted on the rectifier (aftermarket Electrex RR97) and I could not find anyone else complaining of this specific issue. Regulator got RED HOT in a matter...

Hi guys! If you have a 2006 RSV-R I really need your help. Really keen to rebuild my bike after a 125 mph excursion at Snetterton. My only stumbling block (if you'll pardon the pun) is a part number and wiring diagram for the instrument panel connecting block. It's a 2X10 pin connector...

Hi everyone going to be helping my uncle out with the wiring on his bike at weekend Has anyone got any pictures of the cables you have to splice its an 07 factory as he was struggling to find the right ones Or the location an colour of the right one ? Thanks, Tom

Hi, Can anyone send me a couple of photos of which coloured wires go to what coils? Been doing some work on my bike and I can't find the picture I had before for reference. Cheers

Just got some Clear Alternatives led replacement bulbs with built in indicatores which i have fitted to my 2003 Mille,tail and brake lights work ok but not the indicators. They come with a single yellow wire that comes from the back of each bulb and apparantly goes to live on the indicators from...

I did search - found nothing and I know that a few on here have done this... The original rear brake switch is an "always on unless pressed" one, and with the relocation of the master cylinder etc, the AP kit comes with a pressure switch that fits on the mastercylinder. Done, no probs. However...

Hi guys I'm new to the Zone, glad to be here! Have a problem. Binned my lovely 06 RSV1000R at 125mph at Snetterton - and so starts the rebuild. Lots of cosmetic damage, but seems structurally sound. It made it to the grass/I didn't:eek: The first problem is that I have lost the connector block...