setting

Hiya, Tuono newb (2009)....what is the suspension setting stuff in the "settings" in the cluster? I was really curious. thanks!

G'day all, I was curious about my fork adjustment, so I counted the number of turns to full clockwise and discovered mine had been set to 9 turns out. This setting on my 04/2014 build (new in Feb2015) has been brilliant and it was only curiosity that tempted me to confirm the setting (standard...

Everything I can find is for the older bikes with the 2 diagnostic wires by the battery. My 04 Factory only has a 3 wire plug for the Axone. I can get fault codes by holding the lap timer and turning the key to on but this doesn't put me in the mode to set the TPS. My stator finally burned up at...

what is it hand book says 120nm Haynes manual says 80 to 90 nm as there has been a lot of rear wheel bearings fail due to been to tight :crazy

Hello there - got a Dr Rossi chip in the Falco now, and I'm happy with it except for the low rev pick up when it sputters a bit. I've done it as well as I can by sound/feel, but I'd like it done properly by someone with the right equipment. Anyone know anyone good near(ish) to Portsmouth? Thanks...

Hi there, Can anyone recommend anyone near to Portsmouth who has the required equipment and knowledge to set up my Falco with its new EPROM chip? (i've actually got the Dr Rossi one and a FR one and would like to get it set up for both). Cheers Simon

Just picked up my Tuono last week. I want to lower the clutch lever as I have to twist my wrist up to grab the lever. The lever itself is secured by a clamp that is easy enough to adjust. The problem is once I rolled it down, the lever hits the mode setting button. I checked to see if I could...

Hi guys, Taken my wheels off (2003 RSVR) to have new tyres fitted, and seem to have lost my Haynes manual. Can someone please tell me what torque setting I need to do up the caliper mounting bolts (radial) please? Cheers.

hey guys anyone know the torque setting for the radial brake caliper bolts on a 08 plate ? cant see it in the **** manual

hi, can any one tell me a simple way to check the sag on my 05 rsvr, i am a bit of a short *** and considering a lowering kit but every thing i have read say its not a good mod, the shock is set to its shortist lenght and all settings are set to the book so all that is left is to check the sag...

Anybody know what the torque setting is for the large Allen key bolt is fixing swing arm to frame via long pin bolt ? (excuse the retarded description) I don't want to over tighten and crush the Bearings Or under tighten and well ..... U get the idea ? Any help appreciated ..simon

Hi can anybody Give me any advice,just wondering what my redline should be set at,is it personal preference or should it be set to certain revs it's a 2000 model with chip and can,any help would be gratefull

What is the correct torque setting for oil drain plug, can't seem to find it in the manual. Cheers

Read its 50nm with blue thread locker.....seems really low to me:confused

I've got a fault code of -1 wich as far as I know is tps. I don't know if this is right but I'd like to check the tps anyhoos, only ting is I can't find any post or write ups that give the knowledge on this so any help in pointing me in the right direction would be just dandy ta

Hi fellow rsvrs, just bought an 08 reg factory,do i need to get the suspension set to suit my weight? going over the forth road bridge at the weekend i thuoght it was going to know my teeth out ,it seems very hard on rough roads and have to watch how i set my mouth or chipped molars might ensue...

Hi everyone bit bored today bad weather, So I have been in the garage checking my sag values just wondered if there is anyone that can tell me if they seem ok front rear static 31mm 12mm rider 45mm 39mm also how does that compare to some...

Hiya guys, I've got and 05" Factory which I love. The only down side is the speedo keeps re-setting to 0 when the leads are disconnected, even for a few seconds. I know there is a lot of clever people out there..please help.:thumbup cheers Creature

Morning,can someone please tell me how to set time on my 1999 rsv mille.I can set the mph/kph,rev limiter,trip etc but the clock is proving to be difficult.:pirate

Hi Guys Well I'm a new Millie Factory owner (03 plate). Had it a coupel of months only and love it. Took it to Silverstone this weekend for a track outing ... clearly forgetting that I hadn't done a track day for 4 years! Got the suspension fine tuned by 100% which helped smooth it out and build...