replace

Hi guys having a bit of an issue have replace the plates on my rsv Mille 2001, but could not get the pressure plate to sit flush, so I took the slave off fitted the pressure plate and then pushed the piston back on the slave and made it flush now cannot get the slave back on as the push rod is...

As the title says I think I have an issue with the Coil on my 03 milie. When the bike gets hot (Above 85) in city traffic it developed a misfire when accelerating. I'v read here its the coil breaking down because of the heat and expansion breaking the contact on already damaged wires? My...

I currently have a pair of Leo Vinci SBK titanium cans on a gen 2 They drive me nuts as I can't get them level ( boy have I tried) ... and the are long - they extend past the numberplate I would like some cost effective stubbier cans - what is there that is good / well made ? BTW I am not...

Anyone make them?

So one of my first posts here, but a big hello from the Big Smoke :cheers. Am the proud owner of a 2009 Factory which is just mega in every way. Here are a couple pics taken this summer. Having piled the miles on (now at 7.5k miles, she's the daily chariot unless wet), the question is...

OK I've been reading reports that peeps have fitting rear master cylinders off shivers and duc 1098's does anyone or has any one fitted the later 06 onwards rs125 cylinder as it looks pretty much the same just not sure if the mounting holes are the same spacing?? Or does anyone know of any other...

Alright guys I need some help! I just got my new fuel pump in the mail yesterday and it's time to swap it out! Also we have a company bike ride tomorrow and the bikes not going to be up and running til i get done swappin her out! My question to you all is do i have to completely empty the fuel...

So whilst the ***** weather is coming in well.. continuing .. I plan on next month stripping down my brakes giving them a good clean, lube pistons etc put new pads on, discs and levers. Is there a recommended life for brake/clutch lines as i was considering replacing these too ?

For sale is my lovely condition 2007 honda CBF1000 with many extras, there is also a lot of mens clothing and luggage going with the bike, also for the right price i will give up my handy Tomtom rider and bluetooth headset. I have just come back from a trip to Germany with the bike and it was...

I`m assuming its the clutch master. Pull the clutch half way and hold it, it looses pressure you you see the resovoir level rise until levers back to the bar. Let go and grab a fresh pump, fluid level goes back down, as pressure returns, before dropping again. Doh! Is it worth rebuilding it? or...

I have bought an early RSV metal petrol tank to fit on my 2003 bike (last of the Gen 1). Now I need some advice!!! Will the tank filler cap and pump from my plastic tank fit the metal tank??? Will I need to swap the seat for the early smaller unit??? I know the mesh under seat side panels may...

Planning to fit a set of Gilles variobars to a 2003 RSV Mille R (radial brake caliper model) and require longer brake lines. I have noticed the standard braided clutch line and front brake lines are of the same material and have the same text printed on the outer to identify diameter etc...

Due to this: Who do you reckon guys? Bayliss ?

Be honest guys This is what it looked like before

Can't believe it, my new bike and my pride and joy (RSV Mille 2002) ended-up on it's side this morning. Sidestand collapsed while I was warming it up....GUTTED. Filled-up yesterday on the way home - 2 minutes from my house, I guess the weight of a full tank of fuel was just too much. Broken...

Sources in Europe said today that none other than Miguel DuHamel will replace Toni Elias for the Laguna Seca MotoGP event later this month. Elias crashed at the recent Assen race and broke his leg, necessitating a replacement rider for the Fausto Gresini-run team. DuHamel, a former Superbike...