removing

Hi, my 2005 Tuono has has a clip on conversion before i bought it, but I'd now like to revert her to standard. I'd welcome advice on whats required? I think I'll need a replacement fairing bracket as I think mine has been cut... The clutch and brake lines look original so are plenty long...

I slightly bent my handle bar so it causes the throttle to stick open. I got a new one but I can't get the Fork Upper Plate to get the bar off so I can replace it. I have the tool that fits inside the center retaining bolt but nothing to torque it with. I used a pair of vise grips but can't get...

Hi i want to remove the baffles from my akro cans, i have a 11 plate gen2 1000r... Ive heard many conflicting things like switching it to map 2 or dont have to switch it and airbox mod will help it run better or just something like a Bmc race filter would be suffice....any info will be...

Hi can you remove the exausts without removing radiator. I need to remove exausts so I can weld lambda probes for Autotune AT 300. Many thanks for any advice.

So I decided to have the Spyball Patriot 8510 professionally removed from my 2001 Mille, which went ok but now I've got a horrible engine misfire. The reason I had the alarm removed was due to it no longer responding to the key fob, despite following all the realignment instructions. Anyway...

So I decided to have the Spyball Patriot 8510 professionally removed from my 2001 Mille, which went ok but now I've got a horrible engine misfire. The reason I had the alarm removed was due to it no longer responding to the key fob, despite following all the realignment instructions. Anyway...

This is my first post in here because I am neither mechanical nor technical :lol I want to run a power cable from the battery on my 2013 V4R to a sat nav mounted on the handle bars. I take it the best way of doing this would be to run it under the petrol tank? Also, is there a Haynes manual...

Hi anyone. I've recently bought new replacement F/R sprockets for my 03 aprilia tuono aswell as new rear brake disc and pads. And whilst i'm changing those i thought I'd replace bearings to. Well after i removed the circlip I've discovered a little cerosion around clip, which has taken a few...

I decided to overhaul all the bearings in the rear suspension, Gen 2. I have taken off the shocker, dog bone, rear exhaust, no problems. I have taken the long bolt out of the swinging arm pivot, but the swing arm does not want to come out. I see on the right side pivot, there is a...

How the hell does it come off? I've wiggled and pulled and the hammer is next lol Thanks. Mark

Is there any guides to help me remove this damn datatool from my 2002 Mille R?? Currently fitting the Jester kit and could really do with the extra room under the tail too :thumbup Cheers

Hi guys Just trying to replace my sprag clutch. Every time I try and remove the bolts, its spinning the crank. What is the way around this. Cheers in advance.

So, i managed to get a bit of time over the w end to strip the bike down and give it a good clean...... Although the bike is mint on the outside, I don't think the previous owner liked to clean beneath the fairing. It's a little ****** to say the least. Any recommendations on cleaning products...

Hi all, A bit of advice if i may... i need to replace the above on my RSV-R Mille and realising this is a plastic tank i wanted to know the best way of doing it? If it were metal then i'd just peel them off and then use a bit of white spirit to get rid of the glue :dunno but i'm assuming this...

I bought a salvage title very beat up 2000 rsv 1000r, my first Aprilia. I have to remove the triple clamps as they are bent. I have the bike on a rear stand & on a front stand with the forks off, however now I need a way to support the bike without the front stand so I can remove the triple...

I suspect it will only be a matter of time before I ditch the datatool alarm on the bike as its already doing my head in . I've removed a datatool alarm before(very slowly) but the previous owner mentioned that he thinks !! This one might be wired into the bikes immobiliser system ...

Hi guys, any idea how id remove a rear shock spring without causing myself serious injury? I want to get it off to be powedercoated as a bit of the paint has started flaking off. Im guessing let as much compression off with a c spenner but thats as far as ive got! Cheers in advance!

This should be an easy one for you lot! I'm trying to take my swingarm out so I can get the suspension bearings replaced - I have everything off except the spindle. On the left there's the normal 26mm nut, and on the right there's the castellated nut and 14mm hex nut. The Haynes manual says to...

Any tips? I don't want to break the clips or anything else....how do I get the damn thing off :confused

Chaps!! Do any of you know the best method of removing small marks and scuffs from the Swing arm? If anyone of you have done it perhaps you have some advice and tips? I have a few small knocks that happened in the garage and its annoying me that they are there. :rant At the moment im...