head

Hi Guys, I've got a 2003 RSV Mille and want a “untainted” headlight. Part No: AP8124945 Does anyone know of one?

Hello Everyone, I have a 2013 model and have been stuck in traffic recently in some intense heat. The temp gauge goes up to 115 and the red light comes on. Is this normal? I checked and I have enough coolant and the fan is coming on. Thanks for any information, as the manual has nothing...

Hi, anyone managed to successfully remove the outer headlight lens to clean the glass lens inside? Mine nearly failed its MOT last year because of it and its no better this year, mot due shortly!!! Looks to be glued in with silicone or such like.

Can anyone assist and give me the RSV R Factory 2004 bearing part numbers not Aprilia part numbers. Thanks in advance.

Can anybody tell me if the 2014 head lights are the same as the 2011,2012,2013 bikes or have there been any changes. Thanks

Advice needed please. I have noticed on the last few times out when I pull away from a standstill I can feel a bit of movement in the bars that I haven't ever felt before. I'm assuming this is the head bearings although I'm not sure. Can anyone confirm what I think or what it might be and is it...

Hi Im looking for a similar decals as on factory versions of RSV Gen2 a big Lion head.

I have never been a fan of Harleys :no however after today I think I get it :yes called over to my mates garage today for a cuppa n a natter and parked outside was a nice shiny roadster 48 r that turned out to be his new toy :yes to cut a long story short the keys where thrown in my direction...

Hi, do any of the club members make and sell stickers that they can sell via this site? Im considering buying some lion head stickers to put on my Gen 1 but prefer to buy from a member rather than flebay if possible. Any takers ?

HI,IM AFTER RH(AS U SIT ON THE BIKE)HEADLIGHT FOR 2005 GEN 2 RSV1000R.CHEERS:devious

Changed the bearings the other day they were well gone , went out for a couple hours blast after and got home to see fluid all down the left side ?? Thought I had a coolant leak but have come to the cunclusion it was all the grease i shoved on the new bearings that melted . I only put multi...

Ok - potential new owner here Rode a Gen 1 in about 06 up a hillside in Switzerland and loved it ( other than the gold frame). I never really got around to owning one Think about getting a Gen 2 as up right sports bike /occasional track tool ... Would love a factory but can't warrant it as...

So i used my bike at night time yesterday for the first time. And noticed that the headlamp aim goes straight up looked like the bat signal lol. so tried adjusting it today Manuel says just turn the screw but to get the screw i had to the nose cone off which was a nightmare. adjusted it quite...

Hi quick question does any body know the size of the valve shims ( diameter wise ) been offered some KTM ones 9mm thanks eddie

Right, so just following the logical route to a conclusion here really, and with a view to understanding the possibilities and potential of mods......( I read posts a while back of gen2 heads on gen1 engines...soundz painful ! ) 1) - Can the bigger valve heads be supplanted to the early small...

hi all looking for fly wheel retaining bolt 14mm x head if you have one call text 07847490156 thanks....

hi all loo king for fly wheel retaining bolt 14mm x head if you have one call text 07847490156 thanks....

My RSV Factory, bought of a 'yob with too much money & not enough sense' :kicknuts in November, been sat in my garage ever since (apart from a very expensive service/geometry check) waiting for March 1st for the SORN is lifted so I can get it out for its 1st blast :bwtiller Will be changing the...

Has any one got a mint 2002 head light with no marks for sale? Cheers

Hi, has anyone fitted pyramid (make) tapper head stock bearings? did they fit ok? only I read somewhere the some of these aftermarket bearings didn't fit well and can't remember what make they were Thanks