bearing

Genuine Aprilia sprag clutch bearing, only used for 800 miles as the engine was used in a special build with Gen 1 electrics so the whole flywheel was just changed over. This is like new with no slack whatever on the spring, looking for £65 including delivery. Cheers Mark

Genuine Aprilia sprag clutch bearing, only used for 800 miles as the engine was used in a special build with Gen 1 electrics so the whole flywheel was just changed over. This is like new with no slack whatever on the spring, looking for £65 including delivery. Cheers Mark

Can anyone assist and give me the RSV R Factory 2004 bearing part numbers not Aprilia part numbers. Thanks in advance.

In addition to play to the bearings and spare parts is very specific, more effective, if use undeserved, can not reach the expected results, but cannot be easily of bearing lubrication is undoubtedly. In addition to the oil, rotation, as well as their use. First of all, the careful installation...

For bearing seal degree, there are two main factors affecting bearing seal performance, processing and manufacturing precision, cooperation between various parts and assembly quality. To solve this problem must be in-depth study of the two. The influence of the sealed bearing precision...

I've been trolling fleabay and found the size I need for the dogbone, hk1812 x 6 £19.50 free postage (gap bearrings) just a little question will I need to remove the studs on the rear exhaust or can I get away wiv just dropping the link n springs cheers

Anybody replaced their front and rear wheel bearings ? on a gen 2 . Got my wheels on the bench , removed the cush drive housing and dust seals and circlips on both wheels , the bearings have a spacer tube internally between the inner faces of the bearings . this tube fits up so...

Hi guys I have just started replacing my spag clutch. The sprag clutch i have removed is slightly different to the genuine rotax sprag bearing i have removed. I belive that the one i have removed is most probally a BMW sprag bearing. Do you know if the rotax sprag bearing needs a circlip as the...

Replaced my slightly knackered original ball raceu head bearings today with nice new taper roller jobbies that i purchased as a kit off ebay for 24 quid made by pyramid parts that come complete with dust seals aswell. So thought I'd share on here my experience fitting them with a pictorial...

anyone have any advice on how much freeplay there should be on the linkage bearings? I could lift my swingarm up and down about 5mm at the wheel spindle and feel movment at the lingages with fingertips. so i thought the bearings might be knackered. taken it apart and everthing looks like new is...

just changed the top and bottom bearings in my yr 2000 rsvr ohlins shock. had to get the bearings from ohlins as i couldnt find any reference numbers for them but would be much cheaper from a bearing supplier so here is the ref if anyone needs it. (SKF) BLRB 366748 AA

hi guys just a few numbers for you if your looking for bearing or seals for your wheels or whatever ....they do all kinds no need to go to a main dealer or fleebay bayliss trading---- 01772 622543 guys called steve :thumbup royce power ---- 01279 421461

Ok been out on the new bike today and thought the front end felt a little wierd. could feel a clunking though the bars and the bike seemed to not want to go in a straight line seemed to weave around alot. So just had a pull on the front wheel and looks like the bearings are knackered. The wheel...

So after using a suitably sized hammer the rear wheel bearings are out thank Fook....................but the problem is that an outer shell has been left in the wheel:rant:rant How am I gonna get that out as i cant tap from the rear as their is a shoulder ffs. Is it gonna be a dremel job...

I have just taken my rear wheel off to clean etcetc and have come across this bearing that hardly moves. Can i get a replacment from the bearing company? or will I have to go to Aprilia?? Is this suppose to turn Aswell?? and how should I lube the sprocket carrier rubbers? with moly...

98 - 03 RSV Mille Bearing & Seal Guide OK, I needed to replace my front wheel bearings due to a slight rumbling noise and almost passed out when I saw the genuine Aprilia parts costs. :eek: So in true AMB67 tradition I decided to look for a cheaper alternate part, this was when I came up...

2x Wheel bearing Seal 30x47x7 Any idea where i can get some from....:confused Got the bearings but they didnt have or do the seals :dunno Cheers peeps

Hello all I'm confused, I need to get some needle bearings for the rear linkage, the Aprilia part number is AP8110065 but it seems like they are out of stock at most places, so after a little search on the forum I noticed some people have used simplybearings for these before, which is cool so I...

Hi guys, Changed my steering head bearings for Koyo bearings instead of OEM. The Koyos are tapered instead of the roller OEM ****. Koyo bearing number is 32907jr-3. Anyway, put all the front end back together, nipped the top nut up nice and tight so theres no play, then backed it off and...

I'm getting a repetitive 'clunky' type noise from the mid to rear of the bike. At first I thought maybe the chain was a bit dry and a sticky link was to blame but having lubed it this doesn't seem to be the source of the noise. With the bike on a paddock stand the chain seems fine however I...