typical never simple !!! part needed...

D

deano

Discussion Starter
• Dec 28, 2009

• #1

hey guys i love working on my bike cars etc myself etc but nothing is ever as simple as it should be bloody pisses me right off :rant

on this occasion i had a result my parents got me some titax levers for crimbo so went to fit them today....

as i am sure most of you know a piss easy job... brake lever no probs all done:thumbup

clutch lever pissing me off lol

there is a small screw holding a the little bar in place that goes into the master cylinder and its competly ruined so cant take the bits out i need to put in the titax lever.....

so i need to know were i can get the part that sticks out and the round bit that goes in the lever as pictured please ???????

 

C

camngetit

Discussion Starter
• Dec 28, 2009

• #2

will it not drill out

 

D

deano

Discussion Starter
• Dec 28, 2009

• #3

did try but dont think my drill pieces are sharp enough so figured would just get some new bits or see if anyone had any nits kicking around ?

 

M

Mini_Me

Discussion Starter
• Dec 28, 2009

• #4

You are aware that it is a very small allen screw not a normal type screw?

 

RSVkwackers

Joined Nov 2009

540 Posts | 0+

HULL

• Dec 28, 2009

• #5

just get a heat gun on the allen grub screw as its loctited it then it unscrews nice and easy....pull the pin/bar out and refit to the titax levers.....easy.
as far as i know you can't buy the pin/bar seperate you have to get the whole lever

 

K

kawasakiinit

Discussion Starter
• Dec 28, 2009

• #6

cant you soak it in oil over night ? might loosen things up ??

 

M

Mini_Me

Discussion Starter
• Dec 28, 2009

• #7

RSVkwackers said:

just get a heat gun on the allen grub screw as its loctited it then it unscrews nice and easy....pull the pin/bar out and refit to the titax levers.....easy.
as far as i know you can't buy the pin/bar seperate you have to get the whole lever

Click to expand...

Yes you canbuy them seperately. Check the AF1 webshop.

 

D

deano

Discussion Starter
• Dec 29, 2009

• #8

Mini_Me said:

You are aware that it is a very small allen screw not a normal type screw?

Click to expand...

mine was a flat head screw holding mine in a the end untill it was completely ****** and then drilled it lol


AF1 website will have a look for that:thumbup

 

D

deano

Discussion Starter
• Dec 29, 2009

• #9

http://www.af1racing.com/store/Scripts/prodView.asp?idproduct=7756

found it but does anyone know a uk seller ??

 

D

deano

Discussion Starter
• Dec 29, 2009

• #10

that AF1 site would of cost me about 60 squid delivered so got one of ebay for 20 all sorted cheers...

 

RSVkwackers

Joined Nov 2009

540 Posts | 0+

HULL

• Dec 29, 2009

• #11

deano said:

that AF1 site would of cost me about 60 squid delivered so got one of ebay for 20 all sorted cheers...

Click to expand...

good news....glad your sorted....enjoy the levers

 

Sprocker

Joined Oct 2010

4K Posts | 0+

Pontefract

• Dec 30, 2009

• #12

Just fitted some Pazzos to mine tonight and there was no screw in the barrel holding the peg :dunno it was just the same as the brake lever, so just a straight swap :doug

Should i be worried :eatcorn