breaking my tuono

Gabro ECU for Tuono V4 extra 500rpm and revised TC settings £350 (only use extra 500rpm with Ti inlets
Nitron pro race shock £420 fits RSV4 (with high and low speed damping) two springs
Ohlins damper £150 fits RSV4
OEM forks with adriani internals few scuffs £350
OEM bottom yoke £120
Full Aprc Tuono traction control minus quick shifter £800 includes Bosch sensor, CLF ecu, wiring, front and rear sensors, TC + and - controls.
Arrow carbon exhaust with baffle £320
Tuono frame with V5 scuffs £500
Tuono V4 gearbox £550
Subframe £100
Throttlebodies £75
K&N Air filter £20
Brembo M4 Calipers gold £350
Menu switch £45
Start stop switch £25
Original exhaust headers (ideal for modification £75)1x tamburini 24l tank unpainted £470 delivered UK
1x sets RSV4/Tuono V4 Grimeca front brake discs £100
1x FULL front and rear set RSV4/Tuono V4 Grimeca with floating rotor buttons £200
1x STM slipper Clutches, last one, needs a couple of parts ordering (ball bearings and another part) but will sort for buyer £250
1x unused sets of clutch and friction plates believe 09/10 ones £100 per set
3x OEM complete clutch baskets and outer basket £90
3x Factory Magnesium alternator covers £100 each (new)
1x OEM swingarm MINT never been on a bike £250
3x oem water overflow bottles brand new £15


All prices are minus P&P.

I dont get PM's unless I am on my laptop and log in here, [email protected]

I hope you took that apart ..... or was it done for you so to speak ???
Wots the next project bike ??

Oh theres too much stuff to tempt me .... must look away !!!!!

Blown the engine.......think bottom end most likely the crankrod bearing was going to break it this week anyway just now minus the engine

Dan said:

Blown the engine.......think bottom end most likely the crankrod bearing was going to break it this week anyway just now minus the engine

Click to expand...

Sorry to ask mate, but how did you do that?

The V2 engines are supposed to be bulletproof. Are the V4's significantly less so, or was this a one off?

Sorry to hear about the motor Dan, best of luck with whatever enters the garage next

I think it may have been a little low on oil, had not checked it, I was breaking it anyway just a pita I have to get the engine fixed or sell in bits.

Hi Dan, nice to meet you yesterday, just wanna say thanks for the tank, it should help extend the fun between fuel stops.

No probs Dave, nice to meet you too, post a pic of tank once sorted :thumbup

Found out the upper injectors were plugged in incorrectly at 2am, that sorted the stumbling but never got to race as other issues came to light, another trip to Donny the following day to Sort it was negative. Ho hum.

Roll on 2016

Its just been filled n primed, should be ready in the next week or so. I did tell the shop no rush lol. They are definatly not rushing....
https://www.dropbox.com/s/yk4xnfk13ddbfhg/2015-11-09_17.24.54.jpg?dl=0
https://www.dropbox.com/s/cccsi2f9g64vxnu/2015-11-09_17.25.03.jpg?dl=0

shoolboy error never ever ever tell a paint shop theres no rush...

garry said:

shoolboy error never ever ever tell a paint shop theres no rush...

Click to expand...

Well aslong as i get it fitted before next spring haha

Hi Dan
I know it's an old thread now but worth an ask, I'm looking for an exhaust valve actuator motor for my v4r aprc.
Mine apparently is buggered and shop tells me I need a new one. Thought I'd search the forum first for a secondhand one.

Oxfordv4r said:

Hi Dan
I know it's an old thread now but worth an ask, I'm looking for an exhaust valve actuator motor for my v4r aprc.
Mine apparently is buggered and shop tells me I need a new one. Thought I'd search the forum first for a secondhand one.

Click to expand...

you will stand a better chance if you email him bud, the link is in the 1st post

Oxfordv4r said:

Hi Dan
I know it's an old thread now but worth an ask, I'm looking for an exhaust valve actuator motor for my v4r aprc.
Mine apparently is buggered and shop tells me I need a new one. Thought I'd search the forum first for a secondhand one.

Click to expand...

i have one! oh and if you have the triangle its off to the dealer with you!

Hi 4vr
No triangle. My local dealer suggested I look second hand first, hence the post on here. How old is it, does it work and how much do you want for it??

hi dude, i paid £50 for it, yes it works fine, been tested before deciding to go down race ecu road!
pm me if your wanting it!

oh its off a 2014 bike, with 2k on the clock!

Hi Dan,
Have sent you an e-mail to: [email protected]
Phil

Sorry guys, my original account I'm locked out of and whoever owns this place does not answer emails. This is my other account but best off emailing me.

Will get you those pics prob next week Phil as regards when I pick bits up.

no worries Dan